Thursday, September 18, 2014

Bubble Pockets Pattern and Tutorial

Back in July, I used the Retro Reproduction pattern to make a corduroy jumper for my daughter.  To change it up a little I added bright "bubble" pockets:  large pockets that had an exposed lining and were gathered at the bottom, and were accented by piping.  After reading lots of positive feedback (thank you!), it seems that many of you would like to be able to add bubble pockets to your Retro Reproduction dresses as well-- so here's the pattern and tutorial.

Click here for the pattern.

Just as a note, I only drafted one size bubble pocket, and it was originally used on the size 4 Retro Reproduction dress.  Since the pockets don't affect the fit of the dress at all, they can really be any size you'd like.  So to make the pockets larger or smaller, simply change the scale when you print the pattern pieces.

So without further ado...

Bubble Pocket Tutorial 
The pockets should be added to the Retro Reproduction Dress before the side seams are sewn together

1.  Print and cut out the patten pieces.   For each pocket you will need one pocket lining and two pocket exteriors.  For the lining: fold your fabric with wrong sides together.  Place pattern piece on top of the two layers, pin, and cut.  Now you should have two pieces, mirror images, for the left and right pockets.
For the exterior:   Fold your fabric with wrong sides together. Place the pattern piece on top of the two layers, pin, and cut.  Repeat for the pieces for the second pocket.  You should have four exterior pieces, two sets of mirror images. 
Be sure to cut the notches in the exterior pieces, this is where your gathering stitches will go (see step 2). 

2.  On the top edge of the pocket lining, fold over 1/2 inch towards the wrong side and press.

3.  On both exterior pieces use a gathering stitch and sew between the notches, 1/4" from the edge.  Do not gather the stitches yet.


4.  Next prepare your piping. At one end of the piping, pull the cord out approximately 1/2 inch, and then clip the cord.  This will allow you to tuck the piping into the seam allowances later on.


5.   With the right side of the fabric up, line up the unfinished edge of the piping with the unfinished straight edge of the exterior piece.  The end of the cord that you clipped should be inside the casing.  This end should line up with the end of the straight edge, with the empty casing extending beyond the fabric. 


6. Baste the piping to the exterior pocket piece.  Using the stitch lines on the piping as a guide, sew as close to the cording as you can without stitching on it.


7.  With ride sides together, pin the two pieces of the exterior pocket together.  Make sure the side with the piping is on top.  The piping will now be sandwiched between the two pieces.  Sew the two pieces together, stitching on top of the basting stitches.  This will allow you to sew as closely as possible to the piping without seeing it.


8.  Open the two pieces, fold so that the wrong sides are together, and press. 


9.  Pull the gathering stitches on both the top and bottom pieces so that the exterior pieces fit the curve of the lining.  The straight edge of the exterior pieces should run diagonally through the lining, meeting at the opposite corners.  On the top corner, tuck the piping casing behind the lining.  Using a 1/4 inch seam allowance, baste from the top right corner all the way around to the bottom left corner.


10.  Prepare the piping by again pulling out the cording and cutting off approximately 1/2 inch.   Line up the piping with the top right corner, with the empty casing extending beyond the top of the fabric .  With unfinished edges aligned, pin the piping along the entire curved edge of the pocket.  Baste.


11.  On the front of your Retro Reproduction dress, mark along the side seam where you want your pocket to be placed.  Pin the unfinished straight edge of the pocket along the side seam of the dress.  Baste.  Turn the edges of the piping and pocket to the wrong side, so that the seam allowance is in-between the pocket and dress, and just the piping is exposed.  Pin.

12.   Starting at the top inside corner, top stitch along the folded top edge of the pocket, and then "stitch in the ditch" between the pocket and the piping. 


And you're done!  When you sew the front and back of the dress together the raw edges of the pocket will be enclosed in the seam allowance. 

We'd love to see what you're creating with the Retro Reproduction pattern!  So feel free to link up your creations to our flickr page, found here.

1 comment:

  1. These are so cute. They really add a lot of style to the dress/ jumper.

    ReplyDelete